Cuisinart CBT-1000 - PowerEdge Die-Cast Blender Specifications download pdf (Page 6)

OPERATION

1. Place the motor base of your Cuisinart

PowerEdge

1.3 HP Blender on

a flat, sturdy surface. It is important that the surface be clean and dry.

Assemble the blender by following the Assembly instructions (page 4).

Once the jar is assembled and is in position on the motor base, plug the

Cuisinart

PowerEdge

1.3 HP Blender into an electrical outlet.

2. Add all necessary ingredients to the blender jar and replace the cover.

Make sure that the “pour” marking in the cover is aligned with the pour

spout. This will ensure smoother lifting of the lid. You may add more

ingredients by lifting the measured pour lid and dropping ingredients

through the fill area. Replace the measured pour lid after adding

ingredients. Do not put hands in blender jar with blender plugged in.

Note: To remove blender jar cover, lift edge of cover marked “lift” upward.

Lifting measured pour lid will not remove cover.

3. START BLENDING: Press the On/Off button. The red LED indicator light

will illuminate and flash, indicating that the blender is turned on but no

speed has been selected. This is Standby mode.

4. CHOOSE BLENDING SPEED: Press desired function to determine the

speed at which you would like to blend the ingredients. The indicator

light for the activated speed will glow. The blender will now be function-

ing at the desired speed. It is possible to switch speeds without pressing

the On/Off button by simply pushing another speed button.

Note: The Count Up

™

Timer will begin counting when the desired speed

button is pushed. When you switch into a pre-programmed speed, the

timer will reset to support the new command.

Note: At the end of the designated cycle, High or Low, the unit will go

into standby mode. To activate, press High or Low again to start a new

cycle.

5. TO PAUSE OR STOP BLENDING PROCESS

a) To Pause Blending Process: Push the button corresponding to

the speed at which you are currently blending. For example: If you

are blending on High speed, push the High speed button and the

blender will stop blending but the unit will remain on.

Note: By pausing the blending process, you will also pause the timer.

The timer will pause until you start blending again. Changing functions

will reset the timer.

b) To Stop the Blending Process: Push the On/Off button when you are

finished with your recipe and would like to turn the blender off. Pausing

will stop the blender but NOT turn it off.

Note: When you push the On/Off button to power the blender off, the timer

will stop counting and the LCD display will be off. When the blender is

turned back on and a speed button is pushed, the timer will begin to count

from 0:00.

6. TO RESET THE UNIT: This appliance features an advanced resettable

thermal fuse. In the event of an overload condition, the unit will shut

down to protect the motor from overheating. To reset the appliance when

this happens, unplug the unit and let it cool for a minimum of 15 minutes.

Then, reduce the contents of the blender jar or work bowl and/or clear

any jams. Restart the unit as noted in the operating directions.

7. TIMING YOUR RECIPES: The PowerEdge

1.3 HP Blender features a

4-minute Count-Up

™

Timer so that you can time your recipes and guar-

antee perfect results. The timer begins counting from 0:00 as soon as

you push your desired function. The timer will continue to count up even

if you change speeds during blending. You can pause the timer by paus-

ing the blending process. Do this by pushing the button corresponding to

the function at which you are currently blending.

For example: If you are blending on Low and you push the Low function

button, the blender will stop blending and the timer will stop counting,

but the unit will remain on. To continue blending and timing your recipe,

push the function chosen (Low) again. The timer will also stop count-

ing when it reaches 4:00 minutes, and an audible chime will sound. The

blender will go into Standby mode when the timed cycle is finished.

The timer will reset itself when the On/Off button is pushed, a pre-pro-

grammed function is engaged or you change functions.

8. PRE-PROGRAMMED FUNCTIONS: Pulse, Smoothie and Ice Crush are

programmed based on extensive testing in our kitchen and engineering

lab. As part of their programming, the blender will pause between

bursts and cycles. This is normal and by design. Programs run for

20 to 60 seconds.

a) Auto Pulse Mode: The pre-programmed Pulse mode creates a

burst of power for quick, efficient blending. To use the Auto Pulse,

from the Standby (On/Off) mode, push Pulse and the red LED

indicator will flash. Then choose High or Low for auto-pulsing for

up to 2 minutes. The pre-programmed sequences of short bursts

with two- second intervals will commence. The Auto Pulse func-

tion can be used to break apart larger pieces of food or to control

the texture of food when chopping. The Auto Pulse function is

also effective in starting the blending process when you do not

1 2 3 4 5 6 7 8 9 10 11 ... 28 29

Comments to this Manuals

No comments

Cuisinart CBT-1000 - PowerEdge Die-Cast Blender Specifications Page 6

Comments to this Manuals

Related products and manuals for Blenders Cuisinart CBT-1000 - PowerEdge Die-Cast Blender